Skip to main content
Ameerpet, Hyderabad · Classroom & live online
Cloud Soft Solutions

Juniper JNCIA-DC (JN0-281) Exam Guide 2026: Spine-Leaf, EVPN-VXLAN Basics, VLANs and IRB, OSPF, BGP, LAG and BFD, 5-Week Plan and 15 Questions

Juniper JNCIA-DC (JN0-281): 65 multiple-choice questions in 90 minutes on Junos 24.2, no prerequisites, valid 3 years. The five objective areas from Juniper's exam page, a spine-leaf and EVPN-VXLAN primer, VLAN, IRB, LAG and EBGP underlay configuration, a 5-week lab plan and 15 practice questions.

Juniper JNCIA-DC JN0-281 data center exam guide 2026, Cloud Soft Solutions
Last updated · 5 min read · 1,084 words

Juniper JNCIA-DC JN0-281 data center exam guide 2026, Cloud Soft Solutions

JNCIA-DC (exam JN0-281) is Juniper Networks' associate certification for data-centre networking. It covers traditional multitier and IP fabric (spine-leaf) designs, underlay and overlay with EVPN-VXLAN basics, Layer 2 switching, VLANs and IRB, protocol-independent routing, OSPF and BGP for the fabric, and high availability with LAG, graceful restart, BFD and Virtual Chassis. Data centres and GCCs around Hyderabad keep adding capacity, and these are the skills their network teams use. Juniper replaced the older JNCIA-DC exam with the current JN0-281 version on 18 November 2024.

This guide follows Juniper's official JNCIA-DC exam page. It covers the exam facts, the five objective areas, a spine-leaf primer, Junos configuration examples, a 5-week plan and 15 original practice questions.

Quick facts (Juniper, November 2026)

ItemDetail
ExamJNCIA-DC, JN0-281
Questions65 multiple choice
Duration90 minutes
Software versionJunos 24.2
DeliveryPearson VUE, English
PrerequisitesNone
Validity3 years
Next levelJNCIS-DC, then JNCIP-DC and JNCIE-DC

Read the official JNCIA-DC exam page.

Exam objectives (summarised)

AreaWhat it covers
Data Center ArchitecturesMultitier designs; IP fabric (spine-leaf); Layer 2 vs Layer 3 strategies; underlay vs overlay; EVPN-VXLAN basics and purpose
Layer 2 Switching and VLANsEthernet bridging; access and trunk port modes; tagging; IRB interfaces; configuring, monitoring and troubleshooting
Protocol-Independent RoutingStatic, aggregate and generated routes; martian addresses; routing instances and RIB groups; load balancing; filter-based forwarding
Data Center Routing ProtocolsOSPF (LSDB, packet types, router ID, adjacencies, DR/BDR, areas, LSA types, configuration); BGP (messages, attributes, path selection, IBGP vs EBGP, groups and peers, policy)
High AvailabilityLAG, graceful restart and BFD (configure, monitor and troubleshoot); Virtual Chassis concepts

Spine-leaf in plain words

  • Every leaf connects to every spine, and leaves never connect to each other. Any server is the same number of hops from any other, which gives predictable latency.
  • The underlay is a routed IP fabric, often EBGP between each leaf and the spines, or OSPF. ECMP spreads traffic across all spines.
  • The overlay uses VXLAN tunnels between leaves (VTEPs) to stretch Layer 2 segments where needed. EVPN, a BGP address family, carries MAC and IP reachability so the fabric doesn't need to flood.
  • Scaling out means adding spines for bandwidth or leaves for ports, without redesigning the network.

Junos configuration examples

# VLAN with an IRB gateway
set vlans SERVERS vlan-id 10 l3-interface irb.10
set interfaces irb unit 10 family inet address 10.10.10.1/24
set interfaces xe-0/0/1 unit 0 family ethernet-switching interface-mode access vlan members SERVERS
set interfaces xe-0/0/48 unit 0 family ethernet-switching interface-mode trunk vlan members [ SERVERS ]

# LAG with LACP
set chassis aggregated-devices ethernet device-count 2
set interfaces xe-0/0/50 ether-options 802.3ad ae0
set interfaces xe-0/0/51 ether-options 802.3ad ae0
set interfaces ae0 aggregated-ether-options lacp active

# EBGP underlay to a spine with BFD and ECMP
set protocols bgp group UNDERLAY type external
set protocols bgp group UNDERLAY local-as 65011
set protocols bgp group UNDERLAY neighbor 172.16.0.0 peer-as 65001
set protocols bgp group UNDERLAY bfd-liveness-detection minimum-interval 300
set protocols bgp group UNDERLAY multipath multiple-as
set policy-options policy-statement LB then load-balance per-packet
set routing-options forwarding-table export LB

On Junos, load-balance per-packet in the forwarding-table export policy actually hashes per flow on modern platforms. This is a common exam point.

show ethernet-switching table
show lacp interfaces
show bgp summary
show bfd session
show route forwarding-table destination 10.20.0.0/24

5-week study plan

WeekFocusLab (vJunos-switch or vQFX in EVE-NG/GNS3)
1Data-centre architectures; spine-leaf; underlay vs overlay; EVPN-VXLAN purposeDraw a 2-spine, 4-leaf fabric with addressing
2Layer 2 switching, VLANs, trunks, IRBTwo VLANs routed by IRB on one leaf
3Static, aggregate and generated routes; martians; routing instances, RIB groups; load balancing; filter-based forwardingCreate an aggregate route and a routing instance
4OSPF and BGP concepts and configuration; routing policyEBGP underlay across the fabric with ECMP
5LAG/LACP, graceful restart, BFD, Virtual Chassis; reviewAdd BFD, fail a link and time the convergence; book the exam

15 practice questions with answers

These are original questions written for this guide, not exam questions.

1. In a spine-leaf fabric, do leaves connect to each other?
No. Every leaf connects to every spine only.

2. What spreads traffic across all spines?
Equal-cost multipath (ECMP) routing.

3. What is the underlay?
The physical routed IP network that carries the overlay tunnels.

4. What does EVPN add to VXLAN?
A BGP control plane that distributes MAC and IP reachability, which reduces flooding.

5. What is an IRB interface?
A Layer 3 interface for a VLAN, used as that VLAN's default gateway.

6. Access port vs trunk port?
An access port carries one untagged VLAN; a trunk carries several tagged VLANs.

7. What is an aggregate route?
A summary route that's active when at least one contributing more-specific route exists; its next hop is reject or discard.

8. How does a generated route differ from an aggregate route?
A generated route takes the next hop of its primary contributing route, so it can be used as a conditional default route.

9. What are martian addresses?
Addresses Junos ignores in routing, such as 0.0.0.0/8 and 127.0.0.0/8.

10. What are RIB groups used for?
Sharing routes between routing tables, for example between routing instances.

11. What is filter-based forwarding?
Using a firewall filter to send matching traffic to a different routing instance or next hop.

12. In OSPF, which routers elect a DR and BDR?
Routers on broadcast multi-access segments such as Ethernet.

13. Which BGP type runs between different autonomous systems?
EBGP.

14. What does BFD provide?
Fast failure detection, in sub-second times, for routing protocols such as BGP and OSPF.

15. Which protocol negotiates a link aggregation group?
LACP (802.3ad).

Before and after JNCIA-DC

Cloud Soft Solutions in Ameerpet, Hyderabad teaches cloud networking, DevOps and security with real-time projects. See the APEX program and all courses.

📞 Call +91 96660 19191 · WhatsApp · Flat No. 513, 5th Floor, Nilagiri Block, Aditya Enclave, Ameerpet, Hyderabad

Frequently Asked Questions

What is JNCIA-DC?
Juniper Networks' associate certification for data-centre networking, earned by passing exam JN0-281.

How many questions are in JN0-281 and how long is it?
65 multiple-choice questions in 90 minutes.

Which Junos version does JN0-281 use?
Junos 24.2.

When did JN0-281 replace the older JNCIA-DC exam?
On 18 November 2024, according to Juniper.

Are there prerequisites?
No.

How long is JNCIA-DC valid?
3 years.

Share𝕏inf✉
EnrollWhatsAppCall us